First article inspection: complete the characteristic record

A passing dimension does not close a missing material report. Keep each requirement linked to the production article, source evidence, and unresolved exceptions.

Kartik Deshpande··8 min read

A first production unit can pass its recorded dimensional checks while the characteristic record still lacks evidence for a drawing note or material requirement. Run first article inspection against the released design definition, account for each required characteristic, and connect the results to the article and production process inspected. Route missing reports and out-of-tolerance results to named owners before approving the record. A green summary needs the evidence behind every required line.

Keep the inspection activity and its first article inspection report, or FAIR, distinct: the report records what was verified and the supporting evidence. Aerospace programs may require AS9102 through the contract. SAE’s AS9102C scope states that its requirements supplement customer and applicable statutory and regulatory requirements. The process below is a working structure to adapt with your quality owner, not a universal inspection standard.

Stage 1: Establish the requirement and released revision

Owner: quality planning with engineering and contract review. Record why the FAI is required, the part and drawing revisions, applicable specifications, and the customer’s reporting and approval requirements. Separate full inspection scope from a partial review of changed characteristics. The failure point is starting from a familiar template before confirming which contract and revision govern this production run.

For aerospace work, confirm the required standard and revision through the purchase order and applicable customer documents. IAQG’s FAI support page says 9102 may be self-imposed or contractually required. Do not infer that every manufacturer, supplier, or industry must use it. A customer can also require evidence or review steps beyond the form set.

Freeze a controlled reference to the design definition used for this record. Include the model, drawing notes, referenced specifications, and approved changes where they apply. Keep the production order’s configuration alongside the bill of materials, but use the released design requirements to define inspection coverage. A component list alone does not enumerate every dimension or finish requirement.

Stage 2: Assign evidence to each required characteristic

Owner: manufacturing and quality engineering. Build a characteristic register with stable identifiers, design references, acceptance requirements, verification methods, and the operation where evidence will be captured. The failure point is a dimension appearing on the inspection sheet while a drawing note or referenced process requirement never enters the register. Reconcile the register back to the released design before collecting results.

Boeing’s FAI planning requirements call for accounting for design characteristics throughout manufacturing, including applicable requirements in materials, processes, and finish specifications. The page also addresses characteristics embedded in digital product definitions. For your plan, identify evidence that must be captured before later operations conceal a feature, then assign that capture to the responsible operation.

Give repeated features enough identity to connect their required results to their locations. Keep the required units and tolerance notation beside the characteristic so an imported measurement cannot receive a pass status under a different unit. Where a requirement needs a certificate or test report, record that evidence type and reference instead of forcing it into a dimensional measurement field.

Stage 3: Link the article to its production and material records

Owner: production with receiving and supplier quality. Identify the article or articles covered, their production order, and the manufacturing configuration used. Preserve serial or lot references at the level required by the job. The failure point is attaching a valid-looking certificate that belongs to another material lot, revision, or supplier shipment.

Match material and process documents through recorded references. Retain the certificate identifier, issuer, applicable specification and revision, and the link to the material or operation it supports. A shared filename or nearby date is a search clue, not a confirmed match. The lot traceability process covers the physical receipt-to-production links that support this part of the review.

Keep evidence roles separate. A material certificate supports the requirements it covers; it does not establish the diameter of the finished article. An inspection result supports the characteristic and article identified on that result. Ask the quality owner to resolve ambiguous applicability before the document becomes accepted evidence in the FAIR.

An inspection result needs a chain of evidence

Released requirement

Revision and characteristic

Production article

Order and material identity

Verification evidence

Result, report, and exception

A measurement can be within tolerance while its applicability to the required revision or production article remains unresolved.

Stage 4: Capture results without turning blanks into passes

Owner: the assigned inspector or test operator. Record results with characteristic IDs, methods, article references, and supporting reports. Preserve measured values where the verification plan requires them and keep the original inspection output. The failure point is a completed summary row whose source report is missing, unreadable, or associated with the wrong feature.

Consider a hypothetical machined bracket at drawing revision D, identified as article A1 from production order P100. Assume the released requirements call for the dimensions and material evidence shown below. The values and identifiers are invented to illustrate record handling, not a performed inspection. This is an excerpt from a working register, not an official AS9102 form or a complete bracket inspection.

CharacteristicAssumed requirementExample evidenceReview treatment
C1, overall length50.00 ± 0.10 mm50.04 mm, inspection result R1 for A1Within the stated tolerance
C2, bore diameter10.00 ± 0.05 mm10.08 mm, inspection result R2 for A1Outside the upper limit; nonconformance review
C3, specified materialMaterial evidence tied to the consumed lotCertificate not attachedMissing evidence; investigate applicability and obtain report

C1 falls between its calculated limits of 49.90 and 50.10 mm. C2 exceeds its 10.05 mm upper limit by 0.03 mm, so its measured result needs a nonconformance reference and disposition by the authorized quality process. C3 has no supported verification result. Keep that evidence gap distinct from a measured material failure, and do not infer conformity from the dimensional results.

Retain the original values when a reviewer corrects a unit, transcription error, or reference. Link the correction to its reason and the replacement evidence rather than overwriting the earlier result without explanation. A later report may resolve the gap, but the record should still explain what the reviewer knew at each approval step.

Connect the records behind the inspection

Start with permitted characteristic registers, inspection outputs, and the production references that establish their scope.

Stage 5: Route nonconformances and evidence gaps separately

Owner: quality review, with engineering or supplier quality as needed. Give each exception a characteristic, article reference, responsible person, and required resolution evidence. The failure point is using a report-level status to hide whether the issue is an out-of-tolerance feature or a missing attachment. Those conditions require different investigations and may have different approval authorities.

For the bracket example, route C2 through the authorized nonconformance process and retain the actual measurement. Route C3 to the person who can establish the consumed lot and obtain its applicable certificate. Finding a document closes the retrieval task only after someone verifies that the document covers the requirement and material in question. Neither task authorizes an operator to change the requirement.

Use the status fields required by the applicable standard revision. IAQG’s Revision C change summary says Form 1 replaced the former complete/not-complete field with a documented-nonconformance question. Keep your internal missing-evidence queue separate from official form terminology. Copying an old Revision B template can carry obsolete status language into the new record.

Stage 6: Review coverage and preserve the change decision

Owner: the designated FAIR reviewer and any required customer approver. Reconcile the required characteristic register to the results and attachments, then check the applicable review and submission requirements. The failure point is approving a packet because every visible result passes while required characteristics are absent from the packet. Review coverage against the design definition, not against the result count alone.

IAQG publishes Revision C forms and warns that the downloads are not all-inclusive substitutes for the associated standard. Use the controlled forms and instructions your contract requires. Preserve the submitted report version with its evidence, and retain later corrections as identifiable revisions so the reviewer can retrieve what was approved.

Plan the next review when engineering or production changes. Boeing’s change-review requirements call for documented evaluation of changes that invalidate original results, including the authorized decision on full or partial FAI. Apply your own contractual requirements to that decision. An unchanged part number alone does not establish that previous evidence still represents the revised production process.

If inspection, nonconformance, and document approvals need a controlled operating workflow, use the quality management system software comparison to assess those functions. Keep the evidence integration question alongside the workflow question: the system still needs the correct references and approved requirements to evaluate the packet.

Where Permute fits in characteristic evidence review

Permute sells connected business data, custom applications, and governed analysis. For this workflow, we can combine permitted inspection registers in Excel or Google Sheets, supporting documents in Google Drive, and production references from SAP or NetSuite. We preserve source references so reviewers can follow the characteristic to the record used as evidence.

We can apply the declared part, revision, characteristic, and document-matching rules across the review. An unmatched certificate stays unresolved; a nearby filename does not become an approved match. Those rules let a repeated review use the same evidence requirements while retaining the exceptions that need a person’s decision.

A quality lead can ask which required characteristics lack a linked result and which reports refer to a different revision. We can return the supporting records their permissions allow, including through Claude, ChatGPT, or Copilot. The reviewer can then investigate the gap using the evidence rather than relying on a report-level pass flag.

Keep inspection authority and product acceptance with quality

We do not perform the physical inspection, certify compliance, approve an engineering deviation, or grant customer acceptance. This workflow reads approved source data and does not promise QMS dispositions or ERP writes. Any external action needs a supported provider/action scope, current permissions, and approval.

FAI also has a narrower purpose than shipment acceptance. IAQG’s Revision C summary identifies the clarification that FAI is not a product acceptance document. Keep release, shipment, and ongoing inspection decisions under the procedures that authorize them (even when the same evidence supports more than one review). A completed report does not remove those separate obligations.

First article inspection needs a complete characteristic record tied to the released design and the production article inspected. A passing measured dimension leaves a missing material report unresolved, while an out-of-tolerance result requires its own documented response. Reconcile coverage, applicability, and exceptions before approving the record under the required procedure. Preserve that packet and the change-review decision so later production can establish which evidence remains applicable.

Review the missing links in an inspection packet

Bring the released requirements, characteristic register, and unresolved evidence references to a scoped data review.

Questions about first article inspection records

Is a first-piece dimensional check a complete FAI?

It may provide part of the evidence. The required FAI scope can also include material, process, finish, and other design requirements, so compare the check with the full characteristic register and contractual requirements. Passing the dimensions on a shop-floor sheet does not resolve requirements that were never included on that sheet.

How should a missing certificate appear in the review?

Record a missing-evidence exception with the required characteristic, production or material reference, owner, and document needed. Do not mark it as a measured failure or infer a pass. After the report arrives, verify that it applies to the required material and revision before resolving the exception.

Does an unchanged part number avoid another FAI review?

Review the change under the applicable customer and standard requirements. Manufacturing, tooling, or engineering changes can affect whether earlier results remain representative even when the part number stays the same. Preserve the authorized full or partial FAI decision and the evidence supporting its scope.