Use a supplier corrective action request to connect a documented nonconformance with containment, a verified cause, an implemented correction, and evidence that the correction works. Assign an owner and an acceptance decision at each handoff. Close the request after the responsible quality owner accepts the effectiveness evidence, with any remaining containment obligations recorded.
If the same defect returns after a supplier reports retraining, reopen the evidence question. Identify what allowed the defect to occur and what allowed it to escape detection. Sorting a shipment protects the next operation (within the inspected scope), while a corrective action must address the supported cause of recurrence.
Quality owns a problem statement the supplier can investigate
Record the request ID, supplier and manufacturing site, part and revision, affected lot or shipment, and the requirement that the item failed. Include the observation, inspection method, observed quantity, and supporting document or image references. A statement such as poor quality gives the supplier no reproducible condition to test.
Keep the inspected population separate from the affected population. Finding a defect in a sample establishes what was observed in that sample, not the condition of every uninspected unit. Ask the supplier to define the suspected production and shipment boundary, then retain the evidence used to include or exclude other lots.
The ASQ eight-disciplines method separates problem definition, interim containment, verified causes, corrective-action selection, and implementation validation. Use the required customer or supplier format when one applies. The sequence below explains the evidence handoffs without claiming that every supplier agreement requires the same form or deadline.
An ongoing supplier audit checklist examines controls and their operation. A corrective action request follows a specific failure through repair and verification. Link an audit finding when it triggered the request, while preserving the individual defect and its closure evidence.
Purchasing and quality confirm the containment boundary
Identify suspected stock at the supplier, in transit, at receiving, and already issued to production. Have authorized owners decide holds, screening, replacement, or other disposition. Keep each decision tied to the affected lot and quantity; an email saying all stock checked is incomplete without the population, method, date, and result.
Containment can protect supply while the cause remains unresolved. Record who performs the checks, how accepted stock is identified, and what ends the extra control. Do not remove a hold because the supplier has submitted a plan unless the person authorized to release it has accepted the relevant evidence.
Parker’s current supplier quality manual is one customer-specific example: its corrective-action requirements distinguish containment, root causes, action, and verification. Apply the contract and current manual for your own relationship. Another customer’s response times do not become your supplier’s agreed deadlines.
The supplier proves occurrence and escape causes
Ask for a causal explanation tied to the actual process conditions. A loose fixture, an incorrect parameter, or a missed revision remains a hypothesis until the investigation supports it. Retain the observations or tests that distinguish the selected cause from other plausible explanations, including the process version and affected equipment.
Investigate detection separately. If the nonconforming part passed an inspection, determine whether the check covered the characteristic, used the right method, and operated under the applicable conditions. ASQ’s 8D method includes both why the problem occurred and why it went unnoticed. A revised production setting can leave the escape route unchanged.
Require the proposed action to name the supported cause it addresses. Training can be part of an action when the evidence identifies a knowledge or instruction gap. A generic retraining entry cannot establish that a fixture, measurement method, or approval control changed. Assign a person and completion evidence to each action before asking whether it was effective.
Separate the action record from its effectiveness result
Consider a hypothetical request for an out-of-tolerance hole position. Assume the investigation supports fixture movement as the occurrence cause and an inspection method that did not check position as the escape cause. The supplier replaces the locating feature and updates the measurement method. These are example findings, not a diagnosis of a real supplier.
| Decision | Evidence in the example | Owner’s acceptance question |
|---|---|---|
| Containment | Identified suspect lots with hold and screening records | Does the boundary account for shipped and unshipped stock? |
| Implementation | Approved fixture change and revised inspection instruction | Were both supported causes addressed? |
| Effectiveness | Post-change production and measurement records under an approved plan | Does the evidence meet the pre-agreed acceptance criteria? |
Have quality define the effectiveness plan before reviewing the results: which post-change lots or conditions it covers, the measurement method, and the acceptance and escalation rules. That plan must fit product risk and applicable requirements. There is no universal number of clean lots that proves every corrective action successful.
For a simple traceability check, assume the plan calls for three identified post-change lots. Evidence for two lots plus an undated photograph leaves the third lot’s result unresolved. Keep verification open, even if the implementation task is complete. A run with no observed defects supports only the inspected conditions and sample; it does not guarantee future defect-free production.
Occurrence and escape evidence
Approved change and completion record
Results against the agreed plan
Quality closes the request and preserves remaining obligations
Record the accepted results, decision date, and person authorized to close the request. Identify any affected instructions, drawings, inspection plans, or similar processes that need the approved change. If a result fails the acceptance criterion, retain the failed evidence and return the investigation to the appropriate owner instead of replacing the original result with the next successful run.
Keep response timing separate from technical effectiveness. A supplier can respond before the due date while the evidence remains incomplete. The supplier scorecard can report those separate measures without turning a submitted form into a successful correction.
When the defect recurs, link the new observation to the earlier request and review whether the cause, action, or verification boundary was wrong. Preserve both records. This lets the next reviewer distinguish failure of an implemented correction from a different defect that happens to involve the same part.
How Permute connects the request with its evidence
Permute sells connected business data, custom applications, and governed analysis. We can connect permitted supplier and receipt records with Excel action logs and documents in Google Drive, retaining supplier, part, lot, and request references. Ambiguous matches remain visible for quality review.
We apply your definitions of submitted, implemented, verification pending, and accepted across a recurring report. A supplier quality manager can inspect requests marked complete that still lack a referenced effectiveness result, with the underlying documents their permissions allow. Keep the decision owner beside the evidence so a report does not silently grant closure authority.
Inspect one corrective action’s evidence
Connect a permitted request log and its supporting records to see which references are missing.
Keep product disposition and quality acceptance with owners
We do not certify conformity, choose sampling plans, approve engineering changes, or release suspect stock. Qualified owners make those decisions under the applicable contracts and procedures. Confirm available evidence and refresh timing during scoping; a missing attachment is an unresolved record, not proof that the supplier never performed the work.
A supplier corrective action request closes with accepted evidence that addresses the documented failure. Keep containment, cause, implementation, and effectiveness as distinct decisions with named owners. Preserve the affected lot boundary and the agreed acceptance plan. If the defect returns, the retained record should let quality review the earlier decision without reconstructing it from scattered emails.
Review gaps in supplier action follow-up
Bring open requests and their closure evidence to discuss a repeatable view of unresolved obligations.
Questions about supplier corrective action requests
Does replacement stock close a corrective action request?
Replacement can resolve the immediate supply problem under the approved disposition. It does not establish the cause or whether a correction prevents recurrence. Keep the replacement receipt linked to containment while reviewing the remaining action evidence.
How long should a supplier have to respond?
Use the current agreement, customer requirements, and risk-based procedure that apply to the relationship. Record separate due dates for containment, cause analysis, implementation, and verification when the procedure calls for them. Do not borrow another company’s deadlines as a universal rule.
What if the supplier cannot reproduce the defect?
Retain the original observation and compare the investigated part, lot, process revision, and test conditions. Keep the cause unresolved until the evidence supports one, and have quality decide the continuing containment needed. An unreproduced defect does not justify inventing a cause to finish the form.